Difference between revisions of "Huxley"
From Hackstrich
(Bit more work done today.) |
(Saving some options for purchasing.) |
||
| Line 39: | Line 39: | ||
|M3 nut | |M3 nut | ||
|33 | |33 | ||
| − | | | + | |Fastenal? |
| | | | ||
|- | |- | ||
|M4 nut | |M4 nut | ||
|1 | |1 | ||
| − | | | + | |Fastenal? |
| | | | ||
|- | |- | ||
| Line 59: | Line 59: | ||
|30mm M3 cap screw | |30mm M3 cap screw | ||
|1 | |1 | ||
| − | | | + | |Fastenal? |
| | | | ||
|- | |- | ||
| Line 74: | Line 74: | ||
|80mm M6 bolt | |80mm M6 bolt | ||
|1 | |1 | ||
| − | | | + | |Fastenal? |
| | | | ||
|- | |- | ||
| Line 112: | Line 112: | ||
! Part || Qty Req'd || Supplier || Status | ! Part || Qty Req'd || Supplier || Status | ||
|- | |- | ||
| − | | M3x20 Screw||Some | + | | M3x20 Screw||Some||Fastenal? |
|- | |- | ||
| − | | M3x30 Screw||Some | + | | M3x30 Screw||Some||Fastenal? |
|- | |- | ||
| M6 Locknut||100 | | M6 Locknut||100 | ||
| Line 120: | Line 120: | ||
| M6 Nut||100 | | M6 Nut||100 | ||
|- | |- | ||
| − | | M3 Nut||100 | + | | M3 Nut||100||Fastenal? |
|- | |- | ||
| M6x25 Washer||50 | | M6x25 Washer||50 | ||
Revision as of 12:00, 22 December 2011
I'm building a RepRap Huxley, printing parts on the HackLab's Makerbot.
Contents
Components
- Cartesian Bot: RepRap Huxley (formerly Mini-Mendel)
- Extruder/Hot End: Universal Mini Extruder modified for bowden cable
- Electronics: Sanguinololu
Status
- 2011-12-21: Did a bunch more hours of printing with no issues, also converted the frog plate (y-chassis2) from 3d printable STL to laserable DXF.
- 2011-12-11: Searched for a place to buy Sanguinololu PCBs, after shipping all of them are more expensive than just making them myself. Sent gerbers to Laen. Parts still need ordering. Ordered a hot end part set for the Universal Mini Extruder as I have no way to machine the brass parts required.
- 2011-12-09: Pololu order arrived, now have the steppers and drivers required. Still need to order Sanguinololu.
- 2011-12-06: More work on parts lists, printed a bunch of actual bot parts.
- 2011-12-05: Printed the fixed block with no issues. Started putting together parts lists.
- 2011-12-04: Printed all components for the extruder other than the fixed block. The duct-1 component failed 95% through the print, I think it should be okay as-is, but if not a separate extension piece could probably be added. Decided on Sanguinololu electronics, ordered 1x NEMA11 stepper, 3x NEMA14 steppers, and Pololu stepper drivers from Pololu. Still need to order Sanguinololu itself.
Parts Lists
Extruder Cold End
| Part | Qty Req'd | Supplier | Status |
|---|---|---|---|
| M3 washers | 13 | ||
| M4 washers | 2 | ||
| M6 washer | 1 | ||
| M3 nut | 33 | Fastenal? | |
| M4 nut | 1 | Fastenal? | |
| M6 wing nut | 2 | ||
| 12mm M2.5 screws | 4 | ||
| 30mm M3 cap screw | 1 | Fastenal? | |
| 10mm M3 grub/set screw | 1 | ||
| 15mm M4 cap screws | 2 | ||
| 80mm M6 bolt | 1 | Fastenal? | |
| M3 threaded rod 40mm long | 1 | ||
| M3 threaded rod 55mm long | 4 | ||
| M3 threaded rod 80mm long | 2 | ||
| Wire spring - 1mm wire, 4mm ID, 12mm long | 1 | ||
| 626 bearing (6x19x6) | 2 | ||
| 623 bearing (3x10x4) | 1 |
Cartesian Bot
| Part | Qty Req'd | Supplier | Status |
|---|---|---|---|
| M3x20 Screw | Some | Fastenal? | |
| M3x30 Screw | Some | Fastenal? | |
| M6 Locknut | 100 | ||
| M6 Nut | 100 | ||
| M3 Nut | 100 | Fastenal? | |
| M6x25 Washer | 50 | ||
| M3x30 Washer | 50 | ||
| M3 Washer | 250 | ||
| M6 Washer | 250 | ||
| M6 Threaded Rod - 1m | 2 | ||
| Smooth Rod (???) | ??? | ||
| 626 Bearing | 2 | ||
| 623 Bearing | 30 | ||
Parts Printed
Extruder
- All parts printed!
Cartesian Bot
- 1x purge-plate
- 1x x-axis-sandwich-clamp
- 2x x-belt-clamp
- 1x x-blunt-plate
- 1x x-motor-end-clamp
- 2x y-belt-clamp
- 1x y-belt-nut-trap
- 1x z-driven-pulley
- 2x z-bar-top-clamp
