Difference between revisions of "Coduino"

From Hackstrich
(ATmega328p chips are available again!)
(Taking out local regulation, using the stack-through power should be fine.)
Line 5: Line 5:
 
* Standard boot loader will be used.
 
* Standard boot loader will be used.
 
* Serial only in the first revision, no USB-Serial on the board itself (FTDI cables are easy to get now).
 
* Serial only in the first revision, no USB-Serial on the board itself (FTDI cables are easy to get now).
−
* Will communicate with the master Arduino (bottom of the stack) via I2C, leaving all other pins available.
+
* Will communicate with the master Arduino (bottom of the stack) via I2C (with jumpers to disconnect this), leaving all other pins available.
 
* Main headers will just 'stack-through' the master Arduino, the I/O from the Coduino will be broken out on separate headers (maybe with a 'base board' that can connect to stack shields on the Coduino via a cable?).
 
* Main headers will just 'stack-through' the master Arduino, the I/O from the Coduino will be broken out on separate headers (maybe with a 'base board' that can connect to stack shields on the Coduino via a cable?).
 
* Board could have capability for 1, 2, or 4 (or 3 really, but I like more even numbers) processors, and just get stuffed with the desired number for cost control.
 
* Board could have capability for 1, 2, or 4 (or 3 really, but I like more even numbers) processors, and just get stuffed with the desired number for cost control.
−
* Local voltage regulation would be best so as to not overload the master's regulator.
 
−
** Power can be pulled from the Vin pin, though this means (if I'm reading the Duemilanove's schematic right) that no power will be received from the master board when using USB power.  Will likely want to pull from Vin if there's voltage there, otherwise pull from +5v and bypass the local regulator.
 
−
*** Need to test an actual Duemilanove to make sure this is correct.
 
−
** As the Duemilanove gets 3.3v from the FTDI USB-RS232 chip (which we don't have here), we will need a separate regulator for this.
 
 
* I2C would be connected through to each MCU as the communication interface
 
* I2C would be connected through to each MCU as the communication interface
  
 
[[Category:Future Project Ideas]]
 
[[Category:Future Project Ideas]]
 
[[Category:Projects]]
 
[[Category:Projects]]

Revision as of 03:09, 24 September 2011

The Coduino (Coprocessor for Arduino systems) will be an Arduino-compatible CPU/support on a shield, to enable multiprocessor stacks. It may also be made in multi-CPU version (2 or 4 CPUs on a shield) for really cool projects.

  • Will use ATMega328p for compatibility with the Duemilanove board.
    • As of March 2011 these are available again in TQFP and QFN packages.
  • Standard boot loader will be used.
  • Serial only in the first revision, no USB-Serial on the board itself (FTDI cables are easy to get now).
  • Will communicate with the master Arduino (bottom of the stack) via I2C (with jumpers to disconnect this), leaving all other pins available.
  • Main headers will just 'stack-through' the master Arduino, the I/O from the Coduino will be broken out on separate headers (maybe with a 'base board' that can connect to stack shields on the Coduino via a cable?).
  • Board could have capability for 1, 2, or 4 (or 3 really, but I like more even numbers) processors, and just get stuffed with the desired number for cost control.
  • I2C would be connected through to each MCU as the communication interface
Retrieved from "http://hackstrich.sarahemm.net/wiki/index.php?title=Coduino&oldid=712"