Beacon3

Beacon3 will be a beacon for the top of our flag(less?) pole for Burning Man 2011. It will be simpler than Beacon2 as time is limited to get it done, but we want a brighter beacon.

Project Status

• 2011-07-19: Initial design started.
• 2011-07-23: Schematic for LED driver board started and almost completed.
• 2011-07-24: Board layout for LED driver board completed pending final review.
• 2011-07-25: Final review of board layout for LED driver board completed, order submitted to MyRO for manufacturing.
• 2011-07-28: Completed schematic for planar board and began board layout.
• 2011-07-29: 4 Cree MC-E LEDs (on star heatsink/boards) ordered.
• 2011-07-30: Completed board layout for planar board, pending review tomorrow. Started work on remote control interface.
• 2011-07-31: Wrote libraries for the I2C mux (PCA9545) and LED driver (SSL3250). Can't test as the hardware isn't here yet, but both compile.
• 2011-08-01: Completed PCB review, submitted to MyRO for manufacturing. Placed orders with Digikey and Mouser for all required parts.
• 2011-08-03: Received LED driver boards from MyRO, all parts from Digikey and Mouser, and LEDs from LED Supply.
• 2011-08-04: Assembled first LED driver board, which works perfectly! driver board test video

Design

• Beacon Unit
  • Same enclosure as Beacon2 can be used to save time, just remove PCBs and replace with these
  • Planar PCB that fits onto the spindle, which the other boards plug into vertically
    • Single MCU this time, as there are fewer LEDs
    • Same light sensor and (lack of) charging circuitry as Beacon2 can also be used
    • Regulator on planar will only be needed for wireless functionality, MCU can operate over whole battery range as can LED drivers
    • Will use an ATmega328p for the MCU, makes it Arduino-compatible
  • 4 RGBW LED units on Star boards and heat sinks at 12, 3, 6, and 9
    • Using Cree MC-E ~2.5W per component colour RGBW LEDs
  • 4 RGBW LED driver boards (custom) at 1:30, 4:30, 7:30, and 10:30
    • 4x NXP SSL3250A chips on each board looks good to drive the RGBW LEDs
      • Will drive them at 200mA per component colour constantly, and 500mA flashes of 820mS
      • This chip has a fixed I2C address though so an I2C mux would be needed on each LED board
        • The PCA9545 looks perfect for this, I2C controlled 4:1 I2C mux and can be "turned off" so that there's no need for a planar mux
• Remote Control Unit
  • Having a remote that would make the beacon extra-noticeable when a button was pressed would be cool
  • To get long enough range to be useful, we'd want ~50mW
  • XBee is probably the best way to go, but need to look at power draw for the RX side and would have to custom-design a remote control unit
  • Remote Control Unit could just be:
    • Arduino Fio
    • XBee Series 1 RP-SMA (plugs directly into Arduino Fio)
    • Rubber-duck antenna
    • LiIon pack (plugs directly into Arduino Fio)

Wireless Protocol

• Commands are one letter, followed by parameters that vary by function.
• Newlines signal the end of a command
• Beacon3 response has a single character severity code (e for error, i for informational/success), then the rest of the line is free-form text
• Beacon3 response is terminated with a newline, unless otherwise specified
• Command listing:
  • Identify: i
    • Parameter: 3 character device ID followed by the 802.15.4 address of the remote device (i.e. RCD2 for the remote control device at address 2)
    • Identify to the beacon who the remote device is.
  • Flash: f
    • No parameters
    • Flash a unique pattern on the Beacon so it can be identified from a distance
  • Status: s
    • No parameters
    • Ask the Beacon to send back a bunch of status information. Terminated by \0, not \n!
  • Debug: d
    • No parameters
    • Ask the Beacon to send debug information as it beacons, will stop when any character is received from the remote device

EEPROM Log Byte Format

• Bit 0 - Subsystem (0 = core, 1 = mux, 2 = driver)
• Bit 1 - Mux number
• Bit 2 - Driver number
• Bit 3 - Reserved
• Bits 4-7 - Error code
  • Error codes for subsystem 'driver'
    • 0001 = LED open fault (switcher overvoltage)
    • 0010 = LED short fault
    • 0011 = Driver overheat
    • 0100 = Flash timeout