Difference between revisions of "Coduino"
From Hackstrich
(Status update.) |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
== Project Status == | == Project Status == | ||
| + | * 2013-05: Going to call this completed after all, decided against offering it as a product as I don't think there's a big enough market there. All working though, and the design is all open if anyone wants to make one :) | ||
| + | * 2012-06: Putting into dormant status, as I won't have time until after Burning Man as I'm putting all my time into [[Beacon4]]. | ||
| + | * 2012-04: Boards are here, awaiting time to test. | ||
| + | * 2012-03-10: Started/finished schematic for baseboard and submitted to Laen. | ||
* 2012-03-04: Ordered connectors to prototype 'base board' from Digikey. | * 2012-03-04: Ordered connectors to prototype 'base board' from Digikey. | ||
* 2012-03-03: Wrote a token-passing demo, base Arduino injects a token which the 4 CPUs on the Coduino pass around in a ring. I2C bus proved. | * 2012-03-03: Wrote a token-passing demo, base Arduino injects a token which the 4 CPUs on the Coduino pass around in a ring. I2C bus proved. | ||
| Line 25: | Line 29: | ||
* All 4 processors run off a single oscillator using a 4:1 fanout buffer, so they will stay synced up instruction-by-instruction | * All 4 processors run off a single oscillator using a 4:1 fanout buffer, so they will stay synced up instruction-by-instruction | ||
| − | [[Category: | + | [[Category:Completed Projects]] |
| − | |||
| − | |||
Latest revision as of 14:15, 2 June 2013
The Coduino (Coprocessor for Arduino systems) is 4 Arduino-compatible systems on a shield, to enable multiprocessor stacks.
Project Status
- 2013-05: Going to call this completed after all, decided against offering it as a product as I don't think there's a big enough market there. All working though, and the design is all open if anyone wants to make one :)
- 2012-06: Putting into dormant status, as I won't have time until after Burning Man as I'm putting all my time into Beacon4.
- 2012-04: Boards are here, awaiting time to test.
- 2012-03-10: Started/finished schematic for baseboard and submitted to Laen.
- 2012-03-04: Ordered connectors to prototype 'base board' from Digikey.
- 2012-03-03: Wrote a token-passing demo, base Arduino injects a token which the 4 CPUs on the Coduino pass around in a ring. I2C bus proved.
- 2012-02-24: First board assembled, runs 'blink' on all 4 CPUs successfully.
- 2012-02-22: Parts arrived.
- 2012-02-21: Ordered parts from Digikey.
- 2011-10-18: PCBs received.
- 2011-09-30: Completed routing board, added all required silkscreen, submitted to Laen for prototype manufacturing. Need to order parts now.
- 2011-09-29: Almost done routing board.
- 2011-09-26: Started routing board.
- 2011-09-25: Added master reset button and power LED. Schematic passes checklist.
- 2011-09-23: Started working on schematic, now 90% complete. Need to add a master reset button and a power LED.
- Pre-Sept 2011: Put specs and BOM together.
Specs/Brainstorming
- Uses ATMega328p for compatibility with the Duemilanove board.
- Standard boot loader will be used.
- Serial only in the first revision, no USB-Serial on the board itself (FTDI cables are easy to get now).
- Communicates (optionally) with the master Arduino (bottom of the stack) via I2C (with jumpers to disconnect this), leaving all other pins available.
- Main headers just 'stack-through' the master Arduino, the I/O from the Coduino is broken out on separate headers (maybe with a 'base board' that can connect to stack shields on the Coduino via a cable?).
- Board has 4 processors, could stuff half of them for a lower-cost version, though I don't think it would lower the cost that much in the end
- Each processor has a local reset button, and can also be optionally linked to a master reset using jumpers
- All 4 processors run off a single oscillator using a 4:1 fanout buffer, so they will stay synced up instruction-by-instruction
